CCTV Monitor
CCTV monitors are used to watch camera feeds, and this category page explains what to look for in a monitor for that job. It is a category page, not a product page: no single listed model is presented here as the CCTV model, because the listed models are general touch monitors that can be used for surveillance viewing among other applications. A buyer who needs a monitor for a surveillance system should check size, resolution, interfaces and mounting form against the system that will feed it.
What a CCTV monitor needs to do
A surveillance monitor spends long hours showing camera feeds, often several feeds at once on a split screen. The qualities that matter most are therefore a clear image at the viewing distance, interfaces that match the recording equipment, and a housing that suits the place where the monitor will sit. Resolution decides how much detail can be seen in a feed, and a higher resolution helps when a small part of the image needs to be checked. The listed models on this site range from 1024 by 600 at 7 inch to 1920 by 1080 at 11.6 inch and 15.6 inch, so a buyer can compare resolutions model by model rather than assuming that every CCTV monitor shares one resolution.
Interfaces decide what a monitor can connect to, and they differ between models. The models listed on this site use combinations of HDMI, VGA, USB, AV and BNC, and the exact list for each model is shown on its own page. A buyer should check the interface list against the existing equipment before ordering, because an adapter can solve a connector mismatch but cannot add a signal type that the monitor does not accept. The enquiry should list the source equipment and the cable types already in use, so any mismatch is found before an order is placed rather than after delivery.
Choosing a size for surveillance viewing
Screen size is only the diagonal measurement of the display, and it does not by itself describe a monitor. Two monitors of the same size can differ in resolution, in aspect ratio, in brightness, in touch type and in overall dimensions, because the housing and the mounting form add their own measurements. A buyer comparing sizes should therefore read the full specification for each model, including the overall dimensions and the interface list, rather than ranking models by size alone. The product pages on this site keep each model's figures separate for exactly this reason.
For a single camera feed on a desk, a smaller screen can be enough, while a wall-mounted view of many feeds usually needs a larger screen. The small touch page gathers the 7 inch and 8 inch models for a compact viewing position, and the larger listed models suit a fixed viewing station. Touch is not always needed for surveillance viewing: a monitor that only displays feeds may not need a touch layer at all, and the enquiry should say whether touch is wanted, because touch adds cost and a different front surface. The surveillance application page discusses viewing layouts in more general terms.
What this page does not claim
This page does not claim that any listed model is certified for surveillance use, and it does not describe camera equipment, recording equipment or video management software, because those are not the company's products. It does not state a brightness figure for the CCTV category as a whole, because brightness is listed per model. A buyer who needs a specific brightness or a specific interface for a surveillance system should name the model and ask for confirmation in the enquiry.
Models on this page
7 Inch Touch Monitor C0716
1024 by 600, resistive touch, HDMI, VGA, AV, USB and BNC interfaces as listed.
11.6 Inch Touch Monitor C1116
1920 by 1080, IPS panel as listed, HDMI, VGA and USB interfaces as listed.
15.6 Inch Touch Monitor C1516
1920 by 1080, VGA, HDMI and USB interfaces as listed; other values confirmed per model.
Enquiry checklist
Before sending an enquiry, note the screen size, touch type, interface list, quantity and application, and whether the monitor will be open frame, embedded or panel mounted. Minimum order quantity and lead time are unavailable on this site and are confirmed per model in the enquiry. Quotations are confirmed per order.
Send an enquiry | Telephone: 0755-89356766, 137 6020 7772
Frequently asked questions
How do I get a quotation?
Send an enquiry with the size, touch type, interface list and quantity you need, plus the application. Quotations are confirmed per order, and specifications are confirmed per model before payment. This site does not list fixed selling figures.
What certification documents can you provide?
CCC, CE, FCC and RoHS are stated by the company. Certificates are available upon request. If a buyer needs a certificate for a specific model, ask for it in the enquiry and name the model, so the correct document can be checked.
Are the specifications on this page valid for every model?
No. Specifications are shown per model and must not be read across the whole range. Where a value is not listed for a model, the page says to confirm per model rather than filling in a generic figure.