Open Frame Touch Monitor
An open frame touch monitor combines the open frame form factor with a touch layer, so it can serve as both the display and the input device of a built-in product. This category page is the open frame pillar of the site. It describes the form factor and the touch choice in general terms, and it links to the listed models whose touch type is stated on their own pages.
Touch choice for a built-in screen
Touch choice is one of the first decisions in an industrial monitor enquiry, and it should be made from the way the screen will actually be used. A resistive touch layer responds to pressure, so it can be operated with a gloved hand or a stylus, while a capacitive touch layer responds to the touch of a finger and suits a familiar swipe-and-tap style of use. Neither type is better in every setting: the right choice depends on gloves, on whether a stylus will be used, on cleaning routines and on how the screen will be mounted. The model pages on this site state the touch type listed for each model, and where a model lists touch as optional, the enquiry should state which touch type is wanted so the correct version is quoted.
For a kiosk or a control panel, the touch choice also affects cleaning and durability. A screen that will be touched many times a day needs a front surface that can be cleaned without damage, and the touch type should suit the way users will interact with it: quick taps for a kiosk menu, or precise presses for a control screen. The model pages state whether touch is resistive, or resistive or capacitive optional, and the enquiry should name the wanted touch type.
Sizing an open frame touch monitor
Screen size is only the diagonal measurement of the display, and it does not by itself describe a monitor. Two monitors of the same size can differ in resolution, in aspect ratio, in brightness, in touch type and in overall dimensions, because the housing and the mounting form add their own measurements. A buyer comparing sizes should therefore read the full specification for each model, including the overall dimensions and the interface list, rather than ranking models by size alone. The product pages on this site keep each model's figures separate for exactly this reason.
Mounting form decides how a monitor fits into a finished product, and it should be settled before size or touch type is finalised. An open frame monitor is supplied as a panel for building into a cabinet or a kiosk, so the buyer takes responsibility for the surrounding enclosure and for ventilation. An embedded monitor is designed to sit inside an existing opening, while a panel mount monitor is fixed through a cut-out with its front face visible. Each form changes the measurements that matter: overall size, visible area, fixing positions and depth behind the panel. The enquiry should therefore state the mounting form and the available opening, rather than giving only a screen size.
The listed models cover 7 inch to 15.6 inch, so a buyer can choose a size that fits the available opening and the viewing distance. A small opening suits the 7 inch or 8 inch models, while a control cabinet with more front space can take a 10.1 inch or 11.6 inch panel. The overall dimensions on each product page, not just the screen size, should be checked against the opening, because the housing adds width and height around the display area.
Interfaces and host equipment
Interfaces decide what a monitor can connect to, and they differ between models. The models listed on this site use combinations of HDMI, VGA, USB, AV and BNC, and the exact list for each model is shown on its own page. A buyer should check the interface list against the existing equipment before ordering, because an adapter can solve a connector mismatch but cannot add a signal type that the monitor does not accept. The enquiry should list the source equipment and the cable types already in use, so any mismatch is found before an order is placed rather than after delivery.
The host equipment behind an open frame touch monitor usually supplies the video signal and, for a touch model, the touch data over USB. A buyer should therefore check both the video interfaces and the USB connection on the model page, and should confirm the operating system support for the touch layer in the enquiry if the host runs an unusual system. This site does not promise operating system support for any model, because no such statement is listed for the models.
Models on this page
7 Inch Touch Monitor C0716
Resistive touch as listed, for a small built-in screen.
8 Inch Touch Monitor C1208
Resistive or capacitive touch optional as listed.
10.1 Inch Touch Monitor C1016
Resistive or capacitive touch optional as listed.
Enquiry checklist
Before sending an enquiry, note the screen size, touch type, interface list, quantity and application, and whether the monitor will be open frame, embedded or panel mounted. Minimum order quantity and lead time are unavailable on this site and are confirmed per model in the enquiry. Quotations are confirmed per order.
Send an enquiry | Telephone: 0755-89356766, 137 6020 7772
Frequently asked questions
How do I get a quotation?
Send an enquiry with the size, touch type, interface list and quantity you need, plus the application. Quotations are confirmed per order, and specifications are confirmed per model before payment. This site does not list fixed selling figures.
What certification documents can you provide?
CCC, CE, FCC and RoHS are stated by the company. Certificates are available upon request. If a buyer needs a certificate for a specific model, ask for it in the enquiry and name the model, so the correct document can be checked.
Are the specifications on this page valid for every model?
No. Specifications are shown per model and must not be read across the whole range. Where a value is not listed for a model, the page says to confirm per model rather than filling in a generic figure.